The Utilities Window.

Creates a room outline using the specified width and depth. All other values as per defaults under "This Design" - "Room Settings".

Usage:
1. Start a new design by clicking "File" - "New".
2. Click on the "Create new Room" button.
3. Specify the width and height of you new room outline. Click "OK" to create.

Example 1.

A room outline - width 2000, height 4000.

Allows you to insert wall components (doors, windows etc) into an existing run of wall. Allows you to specify the width of the new wall component, but all other values (hinging, style, height off ground) are left as defaults. You may then edit the newly created component once it has been inserted into the wall.

Usage:
1. Highlight the run of wall you wish to insert your new wall component into.
2. Click on the "Wall Helper" button.
3. Choose the type of wall component you wish to insert.
4. Specify the "Distance from start" - this is the distance from the left-most point (or start) of the selected wall section.
5. Specify the width of the new component.
6. Optional - buttress/recess distances are only used when adding a buttress or recess. When using a buttress it is the distance into the room the buttress will project. When using a recess, it is the distance out of the room.
7. Optional - irregular buttress/recess return is only used when adding an irregular buttress or recess. When using an irregular buttress the buttress will project into the room by the buttress distance and out of the room by the irregular return value. When using an irregular recess the recess will project out of the room by the recess distance and into the room by the irregular return value.
8. Click "OK" to insert the item.

Example 1.

A door is added to the left-most wall. 200 from the start of the wall. Width 800. Leave the buttress/recess values as default - they will not be used.

Example 2.

A buttress is added to the section of wall following the door. 500 from the start. 1500 wide. 300 buttress distance (as it's a regular buttress, no need to specify the irregular value - leave as default).

Creates a soil pipe or boxing section in the corner of the room.

Creates an email with with files automatically attached.

Changes from Drag and Drop mode to Normal Mode. Equivalent to clicking "Mode" - "Normal". Normal mode is usually used when creating the Walls layer in your design.

Changes the way doors are drawn on the cabinets in your design from plant-on to in-frame and allows you specify the style of frame and the frame thickness.

NOTE - this can be applied to any door range you have installed.

Usage:
1. Click "Door Frame Type".
2. Select the frame type.
3. Specify the frame horizontal and vertical widths.
4. Click "OK".
5. If you wish to return to plant-on doors after selecting in-frame, click "This Design" - "Room Settings" and un-tick "Doors Have Frames".

Example 1.

Left-hand image without frame, right-hand image has a modern frame, 30 wide horizontally and vertically.

Creates a series of regularly spaced ceiling beams.

Use the multiple select feature of Drag and Drop to move them into place.

Adds another room onto the walls layer.

ArtiCAD is a room design system i.e. it is intended to design one room at a time. However, it is possible to add a second room onto your plan using this wizard. It is intended for creating utility rooms or en-suites. The new room will use the same wall, wall tile and floor colour as the original room - it is possible to change the wall and wall tile colour by editing the individual wall components. You can also use the Wall Helper to add in extra wall components to the second room.

Usage:
1. Select the door or arch that you wish to lead into the new room.
2. Click "Useful Wizards", select "Add another room" and click "OK".
3. Specify the dimensions of the new room. Click "OK".

Example 1.

Using the default values.

Example 2.

Length 1 = 1000, Length 2 = 500, Length 3 = 1200. Door and window added using Wall Helper.

Allows you to alter the tiling on a section of wall.

Turning the tiling on for a section of wall will tile the entire width of that wall section using the same tile from/to values. If you want to have different tiling heights on a wall section (e.g. below a chimney hood) or to stop the run of tiles in line with the end of a run of units, use this wizard.

Usage:
1. Select the run of wall you want to alter the tiling on.
2. Click "Useful Wizards", select "Tiling Area Tool". Click "OK".
3. Specify the width of the new tiled areas (Width of tiled area). You can break the wall up into two or three new tiled areas. The width of the third tiled area is calculated automatically. If the widths of section 1 and 2 add up to the width of the selected wall, the third sectio is ignored.
4. Specify whether the new sections are tiled by ticking the "Tiled" box.
5. Specify the tiling heights for these new areas (if selected).
6. Click "OK".

Example 1.

• Section 1 - width 1200, tiled, from top of base units to bottom of wall units.
• Section 2 - width 600, tiled, from top of base units to 1650.
• Section 3 - width calculated automatically, tiled, top of base units to bottom of wall units.

Example 2.

• Section 1 - width 1000, tiled, top of base units to bottom of wall units.
• Section 2 - width 2000, no tiling.
• Section 3 - not used as section 1 and 2 total the length of the selected wall section.

Calculates the area of tiling specified in your design and the total floor area.

NOTE - does not take into account whether a tiled area is behind a unit. It is the tiled area specified, not the tiled area that is visible. Same applies for the floor area. Figures should be used as a guide only.

Usage:
1. Click "Useful Wizards" and select "Tiling Calculator". Click "OK".
2. The total tiled area and floor area will appear. Click "OK" when finished.

Example 1.

Total tiling and floor area.

Calculates the heights of the left and right sides of an Angled Cut Wardrobe so it fits under a sloped ceiling.

Usage:
1. Click "Useful Wizards", select "Caculate Side Height's of Angled Robe", click "OK".
2. Specify the required information. The wizard works with robes that slope in either direction.
3. Create your Angled Cut Robe using the information provided.

Example 1.

Wedge dimensions - Height off ground = 1200, Depth = 1500, Height = 1200. The Width is 1000, but is not needed for this wizard.

For the right-hand robe, the distance from start of wedge = 0. The robe is 500 wide. The results from the wizard are 1200 for the short side and 1600 for the tall. When creating the Angled Cut Robe, the short side will be the right-hand side, so set the "Height of right-hand side" to 1200. Set the "Height" to 1600.

For the left-hand robe, the distance from start of wedge = 500 (i.e. the width of the right-hand unit). The robe is 600 wide. The results from the wizard are 1600 for the short side and 2080 for the tall. Set the "Height of right-hand side" to 1600 and the "Height" to 2080.

Version 16 - Bay Window wizard.

To run the wizard, click "File" - "Run wizard..." or press "Control"/"Ctrl" and "W" on your keyboard.

There are three ways of specifying the dimensions of the bay window. Select the method using the drop-down box at the bottom of the dialog.

• 1 - you supply the width of the bay opening and the overall depth. The wizard calculates the size of the windows and the angles between to fit the supplied dimensions. Can only have three windows.
• 2 - you supply the width of the bay opening and the length of the window sections making up the bay. The wizard calculates the depth of the bay and the angles between each window section. Can only have three windows.
• 3 - you supply the width of the bay opening, the depth of the bay and the number of window sections making up the bay. The wizard calculates the window section length and the angles between.

Using the wizard.

Draw you room up to the point where the bay would start.

Run the wizard as described above. Choose the method appropriate to the room layout.

The above image shows the options for method 2. Change to the required values and click "OK" to add teh bay onto your design.

Continue drawing the rest of your room as normal.